Fiber Optic Remote for Exelis RO™ Tactical Radio

Model #: PKG-CCRP

PKG-CCRP

Overview

The PKG-CCRP is a two part solution providing a fiber optic remote extension of the Exelis RO™ Tactical Radio handset / data port to a desk set monitor. The solution allows the radio to be mounted in a convenient location to allow a shorter permanent antenna cable, maximizing the signal strength, while allowing the radio to be used in a location where it may not normally function.

>The 2U high rack mount chassis provides power regulation for the radio, local connector access for install verification/configuration/monitoring, and a fiber optic interface for remote connection of the radio accessory port. All installed devices are modular and can be easily accessed from the rear of the chassis. Front panel LEDs show system power and radio PTT status.

The desk set monitor provides for connections of the same radio accessories (handset, headset, PDA device, etc.) as well as a separate rear serial port (standard 9 pin connector) for connection to a PC or other serial device while allowing for monitoring of incoming audio via the desk set speaker. Separate volume controls allows adjustment of the handset volume apart from the monitor speaker volume. The monitor speaker has a mute control, allowing quick silencing of the speaker without having to adjust the volume. LED indictors show the monitor speaker mute status as well as fiber link status. The rear serial port allows simultaneous data and audio use.

PKG-CCRP Rear

Radio Rack (RMC-CCRP):

  • Provides housing and power for an Exelis RO™ Tactical Radio
  • Hot Swappable Redundant Power Supplies
  • Supports all functions of the
    RO ™ Tactical Radio including PTT and serial data connection
  • Front panel access for local handset connection
  • Local / Remote selector
  • Status indicators
  • Includes all radio connections
  • Easy access for external antenna connection

Desktop Remote (CCRP-B):

  • Full handset support
  • Built-in speaker for audio monitoring
  • Separate volume control for handset and speaker
  • D9 Serial port connector for remote radio monitoring

AUDIO SPECIFICATIONS (FOI-7280)

 

Min

Typ

Max

unit

Frequency Response

20 Hz to 25 KHz

-0.5

0

0.5

dB

26 KHz to 45 KHz

-1.5

0

1.5

dB

Third Harmonic Distortion plus Noise (THD+N)* - 1 KHz @ +4 dBu

-

0.015

-

%

Input Level (with max 1% THD)

-60

0

+17

dBu

 

-

 

VDC

Input Sensitivity

0.020

0.775

7

Vrms

Input Noise Floor ref +0 dBu

-

-80

-

dBu

Input Impedance

-

2

-

Output Level

0.02

0.775

7

Vrms

Output Impedance

-

150

-

Ω

Output for Use with Nominal

-

600

-

Ω

Audio Latency (point to point)

-

1260

-

µs

Sampling Rate

24 bit / 96kHz or 24 bit / 48 kHz

*Hum & Noise are measured with an AES17 compliant filter at 20 kHz. Temperature condition @+10 - +25° C.

SERIAL DATA SPECIFICATIONS

 

Min

Typ

Max

unit

RS-232

Output Levels, 3KΩ Termination

±5

±5.4

-

VDC

Input Levels

-15

-

+15

VDC

Input Threshold

±3

-

-

VDC

Data Rate

0

-

1

Mbps

Input Termination

3

-

2.3

ELECTRICAL SPECIFICATIONS

 

Min

Typ

Max

unit

Environmental

Storage Temperature (°C)

-40

-

85

°C

Operating Temperature (°C)

0

-

50

°C

Power Requirement

Voltage Range

7

9

12

VDC

Supply Current, no SFPs

-

600

-

mA

OPTICAL SPECIFICATIONS

External SFP Interface

Min

Typ

Max

unit

Data Rate

-

346

-

Mbps

Recommended Jitter

-

40

-

psec

Operating Voltage

-

3.3

 

VDC

Maximum Current

-

-

500

mA

Optical Modules

SFP MSA (SFF-8431, SFF-8432, SFF-8433) compliant slot, data rate 266 Mbps - 1.25 Gbps

Output Power (50µ fiber)

-9

-

-4

dBm

Extinction Ration

9

-

-

dB

TX Optical Wavelength

830

850

860

nm

RX Sensitivity

-

-

-18

dBm

Max Received Power

0

-

-

dBm

RX Optical Center Wavelength

770

-

860

nm

The CCRP is optimized for 50 micron multimode fiber. This will allow a link up to approximately 2 km, depending on cable grade, number of splices or patch panels, etc. When using 62.5 micron fiber the maximum distance for a link with the CCRP is approximately 1.8 km.

PKG-CCRP

Spare Parts

RMC-CCRP 19 in EIA Rack mount chassis, 3.5 in (2RU) to hold components necessary to house, power and convert Excelis RO Tactical Radio (8241799G8 [NSN 582001C134201]) . Includes front panel connection for local headset,panel indicators and all internal wiring harnesses. Power supplies, CMA-CCRP, CMA-2011 and radio are not included.
PSM-2010 Redundant power supply F/U/W RMC-2xxx series rack mount chassis, 90-260 VAC, 40-400 Hz input, 75 Watts
CMA-CCRP Custom carrier tray for radio with integrated power supply. Radio not included.
CMA-2100 Fiber optic conversion tray. Includes FOI-7280 mounted with fiber jumpers and copper breakout for radio connections.
CCRP-B Remote desktop unit with speaker, handset connection and RS-232 dataport. Accommodates Excelis Noise Cancelling Handset (8241761G1) not included.

How to Buy

We support a variety of clients from multiple markets. To make the buying process the cleanest and most efficient we provide a number of ways to purchase our products.

See our How To Buy page to find the procurment method that works best for you and your business.