The LightViper VIM-MY32 YGDAI cards are designed for use with Yamaha™ digital equipment containing YGDAI (Yamaha General Digital Audio Interface) card slots. The VIM-MY32 cards are used in place of the VIM-1832 at the “tail” or mixer end of the system.
The VIM-MY32 cards can be used in connection with the VIS-1832 or VIS-4832. When used with the VIS- 4832 and Yamaha™ AD8HR mic pre-amps, The Yamaha™ AD8HR mic pre-amps can be remotely controlled through the LightViper system using a Yamaha™ console. VIM-MY32M Master Card – this card provides 16 direct digital inputs (sends) and 8 digital outputs (returns) from the Yamaha™ device.
The VIM-MY32M comes standard with LC fiber connectors however it can also be fit with ST, Neutrik Duo or Neutrik Quad tactical connectors. The VIM-MY32M contains multimode optics (singlemode optional).
The VIM-MY32M contains the clock for the LightViper system. There is an internal switch to select whether the VIM-MY32M is the master clock, or whether the VIM-MY32M will slave to the consoles master clock. The VIM-MY32 cards only operate at 48k. The VIM-MY32M provides 2 fiber-optic pass thru connectors which allow inputs 17-32 to be fed into a second master card. There is a “sync” status LED on the front of the VIM-MY32M. This LED will be solid green when in sync, flashing red and green while looking for sync, and solid red when no sync is present.
The VIM-MY32M contains a Neutrik MiniCon® connector to enable connection to the VIM-MY32S slave card. VIM-MY32S Slave Card – there is no fiber-optic connection to the VIM-MY32S slave card. It connects to the VIM-MY32M master card via the supplied MiniCon® cable. The VIM-MY32S also contains an RJ45 connector for TTL data input, and a DB9, both of which can be used for sending Yamaha™ HA remote control over fiber with the audio returns. The toggle switch is used to choose which connector is active – the TTL connector or the DB9 connector. To use the TTL data port for Yamaha HA remote control, a LightViper DGL-422 dongle is required.
- 32×8 FiberOptic Audio Transport
- Digital direct input to Yamaha™ YGDAI card slots
- Optical distribution of Word Clock
- Transports Yamaha™ HA remote control
- Ultra-low latency cable runs over 1.25 miles with no loss
| GENERAL SPECIFICATIONS | ||||
|
Min
|
Typ
|
Max
|
||
| Power Consumption From Card Slot (W) |
-
|
3.5
|
-
|
|
| THD+N (1kHz@ +4dBu) | < 0.01% | |||
| Frequency Response (20-20kHz @ +16 dBu) | ± 0.5 dB | |||
| Dynamic Range | 102 dB | |||
| Crosstalk | 5 dB above noise floor | |||
| Sampling Rate | 24 bit / 96kHz or 24 bit / 48 kHz | |||
| Latency | 630 μs analog input to analog output, 20 μs, digital input to digital output | |||
| Environmental | Storage Temperature (°C) |
-40
|
-
|
85
|
| OperatingTemperature (°C) |
0
|
-
|
50
|
|
|
PHYSICAL DIMENSIONS
|
|||
|
Height
|
Width
|
Length
|
Weight
|
|
1.575 in (40 mm)
|
4.74 in (100 mm)
|
6.392 (161 mm)
|
0.8 lb (0.4 kg)
|
| OPTICAL CHARACTERISTICS | ||||||
|
Fiber
|
Size
|
Max Distance
|
Wavelength
|
Output Power
|
RX Sens | Loss Budget |
|
Multimode
|
62.5 / 125 μm
|
2 km
|
820 nm
|
-18 dBm
|
-30 dBm
|
12 dB
|
| Singlemode |
9 /125 μm
|
20 km
|
1300 nm
|
-15 dBm
|
-32 dBm
|
21 dB
|
